Bottom Brackets

BSA is equivalent to English threading. English threading on road bikes mean a 68mm-wide, 34mm inside diameter shell with reverse threading on the drive side. It's the most common threaded standard employed today. This kit works with 24mm diameter cranks, such as Shimano, FSA, Rotor, and others. Choose between two bearings for the cups. Standard Bearings have low drag thanks to hardened-steel races and our Ceramic balls. Coated Bearings have those same balls installed on coated, hardened-steel races for longer life and less bearing drag. English threading is easy to work with, and 24mm spindles easily fit through the shell, allowing for large bearings to be employed in the outside cups. Put more of your energy into forward motion by reducing frictional drag wherever you can. CeramicSpeed Standard Bearings typically have frictional drag of 0.3-0.4 watts per set. That's in the range of a 75% drag reduction compared to standard bottom brackets. CeramicSpeed balls are 100% smoother and 15% harder than ceramic competition. The bearings last at least 3x longer than other bearings. In The Box: - 2 threaded cups with bearings - 2 dust covers with built-in spacers - Spacer tube - 10mm syringe of All Round Grease - Sticker sheet

The PF30 standard is widely used. To make it compatible with Shimano and other 24mm diameter cranks, as well as improve the system, select this bottom bracket. The package comes with two cups and CeramicSpeed Bearings installed. The cups have extended inner sleeves and join with a center section, reducing the likelihood of creaking and increasing the reliability of the system while also eliminating spindle rub on internal cables. The cups mate with 24/22mm crank spindles. There are two bearing options. Both Standard and Coated Bearings feature super smooth CeramicSpeed Balls and hardened-steel races. The CeramicSpeed Coated Bearings have an additional feature: a 3-micron thick metallic layer over the races. This addition makes the races smoother and harder, lowering drag and increasing life. The CeramicSpeed Standard Bearings have only 0.3-0.4 watts of frictional drag per set, an average drag reduction of 75% compared to stock bottom brackets. This is the result of great design, including hardened-steel races and CeramicSpeed Balls that are 100% smoother and 15% harder than the ceramic competition. They also last longer. The CeramicSpeed Coated Bearings last even longer and feature even lower drag. Life increases by 60% and drag drops by 50% compared to our CeramicSpeed Standard Bearings. All Round Grease is installed in the bearings. It can be replaced for lower-drag TT and Track Grease or higher-durability LongLife Grease, which adds a bit of drag but stays in the bearing when riding through messy conditions. In The Box - 1 bottom bracket with bearings installed - 2 dust covers - 10ml syringe of All Round Grease - Sticker sheet

The PF4130 bottom bracket is Press Fit into 41mm diameter shells that are 86.5mm wide and mate most cranks with a 30mm spindle to that standard. If you have a BB86 frame and want to install a 386EVO crank or Rotor 30mm crank, this is the kit you need. CeramicSpeed bearings are installed in cups. The Standard Bearing has ceramic CeramicSpeed balls and hardened-steel races. The Coated Bearing has the same balls running on hardened-steel races with a 3-micron-thick metallic coating making the races harder and smoother, increasing service life and reducing friction. Enjoying the benefit of a massive, strong, and light 30mm crank spindle in your BB86 frame is possible with this kit. Press in the cups, set up the wave washer, add spacers if necessary, and torque down. CeramicSpeed's bottom bracket is also stiff and light, but its greatest benefits come in the form of drag reduction. Standard Bearings with stock grease typically have frictional drag of 0.3-0.4 watts per set. That's about a 75% drag reduction compared to conventional bottom brackets. The bearings also last at least three times longer than other bearings. Performance can be tuned by replacing grease. All Round comes with this BB, but you can change it to TT and Track Grease for less drag or to LongLife for greater durability. In The Box - 2 cups with bearings installed - 2 1mm spacers - 2 0.5mm spacers - 2 dust covers - O-ring - Plastic cable protector - 10ml syringe All Round Grease - Sticker sheet

The new SRAM DUB crank standard, built on a 28.99mm spindle, allows for a more contamination-resistant BB design while retaining the ultra-efficient & long-lasting qualities CeramicSpeed Bottom Brackets are known for. With an integrated dust cover for all models, the snug & secure fit not only fully protects the face of the bearing, but also delivers exceptional performance without any sacrifices. CeramicSpeed hand-built bearings carry the load from crank to frame with unparalleled durability & efficiency. The SRAM DUB crank spindle requires the bearing contact points to be in a set and designated width and all CeramicSpeed bottom Bracket options perfectly match the bearing placement on the crank spindle with the required frame interface for nearly any model of bike. Without the use of unnecessary adapters or spacers, a quiet & stable platform is ensured throughout the life of the product. The BB30 for SRAM DUB Road comes in two versions; one using our CeramicSpeed Standard Bearings and the other using our Coated Bearings for even longer lifetime and lower friction. Compatible with: - Frame: BB30 - Opening diameter: 42mm - Shell width: 68mm - Bottom Bracket Tool for installation: BBT-79 In the box: - 2 cups with CeramicSpeed Bearings installed - 2 dust covers - 4 x 1mm spacers - 10ml syringe of CeramicSpeed All Round Grease - Sticker Sheet

The BB30 standard opened up design possibilities for frames. Adapting it for Shimano cranks takes a special machined aluminum threaded bottom bracket that threads into itself. Ours are finished with CeramicSpeed Bearings. You have two choices in terms of bearings. The first choice is our low drag, long life standard bearing with hardened-steel races and our super-round CeramicSpeed Balls. The second choice is our coated bearing, which uses those same balls installed on coated, hardened-steel races for longer life and less bearing drag. This bottom bracket works with cranks that have 24mm spindles. Bottom brackets have several variables, but within that, CeramicSpeed standard Bearings typically have frictional drag of 0.3-0.4 watts per set. That's in the range of a 75% drag reduction compared to standard bottom brackets. That's thanks to balls that are 100% smoother and 15% harder than the ceramic competition. The CeramicSpeed Bearings last at least three times longer than other bearings. Coated Bearings see another big bump in performance. The coated races see a 50% drag reduction and an improvement in bearing life of 60%. Performance can be tuned by changing the grease. All Round Grease comes installed, but can be changed for lower drag TT and Track Grease, or higher durability LongLife Grease, which adds a bit of drag but stays in the bearing when riding through messy conditions. In The Box: - 1 bottom bracket with bearings installed - 2 dust covers installed - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet

The new SRAM DUB crank standard, built on a 28.99mm spindle, allows for a more contamination-resistant BB design while retaining the ultra-efficient & long-lasting qualities CeramicSpeed Bottom Brackets are known for. With an integrated dust cover for all models, the snug & secure fit not only fully protects the face of the bearing, but also delivers exceptional performance without any sacrifices. CeramicSpeed hand-built bearings carry the load from crank to frame with unparalleled durability & efficiency. The SRAM DUB crank spindle requires the bearing contact points to be in a set and designated width, and all CeramicSpeed Bottom Bracket options perfectly match the bearing placement on the crank spindle with the required frame interface for nearly any model of bike. Without the use of unnecessary adapters or spacers, a quiet & stable platform is ensured throughout the life of the product. You have two bearing choices. The first choice is our low drag, long life Standard Bearing with hardened-steel races and our super-round CeramicSpeed balls. The second choice is our Coated Bearing, which uses those same balls installed on coated, hardened-steel races for longer life and less bearing drag. Compatible with: - Frame: BB86 - Opening diameter: 41mm - Shell width: 86.5mm In the box: - 2 CeramicSpeed Bearings - 2x dust covers - Plast-sheet - 4 x 1mm spacers - 10ml syringe of CeramicSpeed All Round Grease - Sticker Sheet

Shimano cranks fit into BB86 frames when you have this CeramicSpeed Bottom Bracket installed. The kit consists of two cups that are pressed into either side of the central opening. The cups come with CeramicSpeed Bearings installed. There are two versions. The first is our low drag, long life Standard Bearing with hardened-steel races and our super-round CeramicSpeed Balls. The second version is our coated bearing, which uses those same CeramicSpeed Balls installed on coated, hardened-steel races for longer life and less bearing drag. This CeramicSpeed BB86 Bottom Bracket works with cranks that have 24mm spindles, including both Shimano and FSA. CeramicSpeed standard Bearings typically have frictional drag of 0.3-0.4 watts per set. That represents an average 75% drag reduction compared to standard bottom brackets. The hardened-steel races feature the CeramicSpeed Balls that are 100% smoother and 15% harder than the ceramic competition. The CeramicSpeed Bearings last at least three times longer than other bearings. Coated Bearings drop friction further and increase lifespan. The coated races see a 50% drag reduction and an improvement in bearing life of 60%. In The Box: - 2 bottom bracket cups with bearings installed - 2 dust covers with integrated spacers installed - Spacer tube - 10ml syringe of All Round Grease - Sticker sheet

These bottom brackets are equipped with hand-built coated bearings specially developed for off-road performance that offer extreme durability and feature a unique design for SRAM DUB 28.99mm cranks. Coated bearings utilize the highest-quality CeramicSpeed ceramic balls, running on hardened-steel races with a 3-micron-thick metallic coating that makes the races corrosion-resistant, harder, and smoother, increasing service life and reducing friction. - This product has a unique design specifically for SRAM DUB 28.99mm cranks - Native fit frame interface and no plastic adapters or excess spacers - This design features a custom integrated dust cover for maximum durability In the box: - 2 CeramicSpeed Bearings - 2 dust covers - Plast sheet - 1 x 3mm spacer - 2 x 1mm spacers - 10ml syringe of CeramicSpeed Long Life Grease - Sticker sheet

The BB86 mountain bike standard was designed to integrate bearings into the bottom bracket for weight reduction. This kit works with the standard: it consists of two cups that are pressed into either side of the shell. There are two versions of this bottom bracket. Both come with CeramicSpeed Bearings installed into cups. The first is our long-life, low-drag Standard Bearing with hardened-steel races and our CeramicSpeed super-round, super hard balls. The second is our Coated bearing, which uses those same CeramicSpeed Balls installed on coated, hardened-steel races for longer life and less bearing drag. This CeramicSpeed BB86 Bottom Bracket meshes with cranks that have 24mm spindles, including both Shimano and FSA. CeramicSpeed standard Bearings typically have frictional drag of 0.3-0.4 watts per set. That means an average 75% drag reduction compared to standard bottom brackets. The hardened-steel races feature CeramicSpeed Balls that are 100% smoother and 15% harder than the ceramic competition. The CeramicSpeed Bearings last at least three times longer than other bearings. Coated Bearings drop friction further and increase lifespan to applying a coating to the races. The coated races see a 50% drag reduction and an improvement in bearing life of 60%. In The Box - 2 bottom bracket cups with bearings installed - 2 dust covers with integrated spacers installed - Spacer tube - 10ml syringe of LongLife Grease - Sticker sheet

BBright is the Cervelo bottom bracket standard found on most of their frames, save the P5. In order to fit Shimano and FSA cranks into this oversized shell, this bottom bracket, complete with CeramicSpeed Bearings, needs to be pressed in. The BBright bottom bracket comes with either CeramicSpeed Standard or Coated Bearings installed. Super smooth, super-round CeramicSpeed Balls contained in hardened-steel races are found on both versions. The Coated version has a metallic coating laid onto the races, making it even smoother and harder, resulting in lower drag and longer life. BBright is similar to BB30, but is wider on the non-drive side. As such, the bottom bracket for running 24mm diameter cranks from Shimano, FSA, and others, is unique. The CeramicSpeed Standard Bearings last at least three times longer than other bearings. Thanks goes to hardened-steel races and CeramicSpeed Balls that are 100% smoother and 15% harder than the ceramic competition. These have a frictional drag of 0.3-0.4 watts per set, which represents an average 75% drag reduction compared to most BBs. The CeramicSpeed Coated Bearings reduce drag by 50% compared to CeramicSpeed Standard Bearings, and show an improvement in bearing life by 60%. In The Box - 1 bottom bracket with bearings installed - 2 dust covers - 10ml syringe of All Round Grease - Sticker sheet

The new SRAM DUB crank standard, built on a 28.99mm spindle, allows for a more contamination-resistant BB design, while retaining the ultra-efficient & long-lasting qualities CeramicSpeed Bottom Brackets are known for. With an integrated dust cover for all models, the snug & secure fit not only fully protects the face of the bearing, but also delivers exceptional performance without any sacrifices. CeramicSpeed hand-built bearings carry the load from crank to frame with unparalleled durability & efficiency. The SRAM DUB crank spindle requires the bearing contact points to be in a set and designated width, and all CeramicSpeed Bottom Bracket options perfectly match the bearing placement on the crank spindle with the required frame interface for nearly any model of bike. Without the use of unnecessary adapters or spacers, a quiet & stable platform is ensured throughout the life of the product. The BSA for SRAM DUB Road comes in two versions. The first is our low drag, long life Standard Bearing with hardened-steel races and our super-round CeramicSpeed balls. The second is our Coated Bearing, which uses those same balls installed on coated, hardened-steel races for longer life and less bearing drag. Compatible with: - Frame: BSA - Opening diameter: Threaded - Shell width: 68mm In the box: - 2 cups with CeramicSpeed Bearings installed - 2 dust covers - 4 x 1mm spacers - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet - Spacertube

BSA is equivalent to English threading. English threading on MTBs mean a 73mm-wide, 34mm-inside-diameter shell with reverse threading on the drive side. It's the most common threaded standard employed today. This kit works with 24mm diameter cranks, such as Shimano, FSA, Rotor, and others. Choose between two bearing types for the cups. Standard Bearings have low drag thanks to hardened-steel races and our Ceramic balls. Coated Bearings have those same balls installed on coated, hardened-steel races for longer life and less bearing drag. For MTBs, English threading, thanks to history, is pretty much the one threaded standard. It works great. 24mm spindles easily fit through the shell, allow for large bearings to be employed in the outside cups. What's more, they rarely creak and seal up well. Lots of things slow bikes down; bearings shouldn't be among them. CeramicSpeed Standard Bearings typically have frictional drag of 0.3-0.4 watts per set. That's in the range of a 75% drag reduction compared to standard bottom brackets. The bearings last at least 3x longer than other bearings. Coated bearings have even less drag. These bearings come packed with LongLife Grease, best for muddy conditions. For less drag when riding in cleaner environs, you can coat the bearings with either All Round Grease or lowest drag TT and Track Grease, which is designed for clean conditions. In The Box - 2 threaded cups with bearings - 2 dust covers with built-in spacers - Spacer tube - 10ml syringe of LongLife grease - Sticker sheet

BSA is another way of stating English threading. The initialization comes from Birmingham Small Arms, which made bicycles. English threading on road bikes mean a 68mm-wide, 34mm-inside-diameter shell with reverse threading on the drive side. It's the most common threaded standard employed today. This kit allows you to fit 30mm cranks, like those from Rotor, to fit in the tight space of this 34mm spindle. Choose between two bearings types for the cups. Standard Bearings have low drag thanks to hardened-steel races and our CeramicSpeed Balls. Coated Bearings have those same balls installed on coated, hardened-steel races for longer life and less bearing drag. Note that the threaded extensions of this BB's cups that thread into the frame are thin, as they need to fit a 30mm spindle inside the cups. CeramicSpeed standard bearings typically have frictional drag of 0.3-0.4 watts per set. That's in the range of a 75% drag reduction compared to standard bottom brackets. That's thanks to balls that are 100% smoother and 15% harder than the ceramic competition. The bearings last at least 3x longer than other bearings. In The Box: - 2 threaded cups with bearings installed - 2 1mm spacers - 2 0.5mm spacers - 2 dust covers - O-ring - 10ml syringe All Round Grease - Sticker sheet - Spacertube

BSA comes from Birmingham Small Arms, aka English threading. English threading on mountain bikes means a 73mm-wide, 34mm-inside-diameter shell with reverse threading on the drive side. It's the most common threaded standard employed today. This kit allows you to fit 30mm cranks, like those from Rotor or RaceFace, to fit in the tight space of this 30mm spindle. CeramicSpeed Coated Bearings are hand-built with unique CeramicSpeed Ceramic Balls installed on coated, hardened-steel races for longer life and less bearing drag compared to standard bearings. In The Box - 2 threaded cups with bearings installed - 2 1mm spacers - 2 0.5mm spacers - 2 dust covers - O-ring - 10ml syringe All Round Grease - Sticker sheet

The EVO386 standard is designed for oversized spindles. CeramicSpeed's kit for Shimano allows you to install Shimano or FSA cranks with 24mm spindles. The cups come with CeramicSpeed Bearings installed. Both CeramicSpeed Standard and Coated Bearings are available. Both utilize super smooth CeramicSpeed Balls and hardened-steel races. The latter has an additional metallic coating on the races to further smooth and harden the steel, further increasing life and lowering drag. The design of overlapping cups extending through the shell for EVO386 reduce the likelihood of creaking and increase the reliability of the system. The CeramicSpeed Standard Bearings feature an average drag reduction of 75% compared to stock bottom brackets. That translates into frictional drag of 0.3-0.4 watts per set, which is the result of great design, hardened-steel races, and ceramic balls that are 100% smoother and 15% harder than the ceramic competition. The CeramicSpeed Coated Bearings are a step up as they reduce drag by 50% compared to our Standard Bearings and an improvement in bearing life by 60%. All Round Grease comes standard in the bearings, but can be replaced for lower drag TT and Track Grease or higher durability LongLife Grease, which adds a bit of drag but stays in the bearing when riding through messy conditions. In The Box: - 1 bottom bracket with bearings installed - 2 dust covers - 10ml syringe of All Round Grease - Sticker Sheet

The new SRAM DUB crank standard, built on a 28.99mm spindle, allows for a more contamination-resistant BB design while retaining the ultra-efficient & long-lasting qualities CeramicSpeed Bottom Brackets are known for. With an integrated dust cover for all models, the snug & secure fit not only fully protects the face of the bearing, but also delivers exceptional performance without any sacrifices. CeramicSpeed hand-built bearings carry the load from crank to frame with unparalleled durability & efficiency. The SRAM DUB crank spindle requires the bearing contact points to be in a set and designated width, and all CeramicSpeed bottom Bracket options perfectly match the bearing placement on the crank spindle with the required frame interface for nearly any model of bike. Without the use of unnecessary adapters or spacers, a quiet & stable platform is ensured throughout the life of the product. The PF30 for SRAM DUB Road comes in two versions. One version uses our low-drag, long-life Standard Bearing with hardened-steel races and our super-round CeramicSpeed balls. The second version uses our Coated Bearing, which uses those same balls installed on coated, hardened-steel races for longer life and less bearing drag. Compatible with: - Frame: PF30 - Opening diameter: 46mm - Shell width: 68mm In the box: - 2 cups with CeramicSpeed Bearings installed - 2 dust covers - Spacer-tube - 4 x 1mm spacers - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet

The PF30 standard has opened design possibilities for mountain bikes. Our CeramicSpeed PF30 Shimano MTB Bottom Bracket gives you the ability to install Shimano and other 24mm diameter spindle cranks on your PF30 MTB. Our PF30 cups have extended sleeves and join with a center section, reducing the likelihood of creaking and increasing the reliability of the system. There is both a Standard and Coated version. Both feature super smooth CeramicSpeed Balls and hardened-steel races. The CeramicSpeed Coated Bearings have an additional benefit: a 3-micron thick metallic layer over the races. This addition makes the races harder and smoother, lowering drag and increasing life. The CeramicSpeed Standard Bearings have only 0.3-0.4 watts of frictional drag per set, an average drag reduction of 75% compared to stock bottom brackets. This is the result of great design, including hardened-steel races and CeramicSpeed Balls that are 100% smoother and 15% harder than the ceramic competition. They also last longer. If you want longer life and even lower drag, opt for the CeramicSpeed Coated Bearings. Life increases by 60% and drag drops by 50% compared to our CeramicSpeed Standard Bearings. Performance can be tuned by changing the grease. LongLife Grease comes installed, but can be changed for lower-drag All Round Grease for lower drag and cleaner riding conditions. In The Box - 1 bottom bracket with CeramicSpeed bearings installed - 2 dust covers - 5 0.85mm spacers - 10ml syringe of LongLife Grease - Sticker sheet

The BB30 bottom bracket allows you to pair 30mm spindle cranks to 42mm inner diameter bottom bracket shells. Cannondale pioneered this standard along with specially-designed cranks and many have found the benefits to them. Road versions have a 68mm width, MTB has 73mm. These are also the bearings you can use to replace bearings in PF30 cups. You have two bearing choices. The first choice is our low drag, long life Standard Bearing, with hardened-steel races and our super-round CeramicSpeed balls. The second choice is our Coated Bearing, which uses those same balls installed on coated, hardened-steel races for longer life and less bearing drag. BB30 was designed to make the bike lighter: no cups, threading, or redundant metal, plus a lighter, stiffer crank. That's why the crank spindle is 30mm, which was a big jump up from square-taper spindles. CeramicSpeed standard bearings typically have frictional drag of 0.3-0.4 watts per set. That's in the range of a 75% drag reduction compared to standard bottom brackets. That's thanks to balls that are 100% smoother and 15% harder than the ceramic competition. The bearings last at least three times longer than other bearings. In The Box - 2x bearings - 2x 1mm spacers - 2x 0.5mm spacers - 2x dust covers - O-ring - 10ml syringe of grease - Sticker sheet

BB90 is the Trek oversized bottom bracket standard and is only found on Trek road bikes. The shell is 90.5mm wide and is designed to work with 24mm spindles and road cranks and have the bearings inside the shell. The CeramicSpeed Bearings come as two bearings, which are then pressed into the frame. Those two bearings consist of either CeramicSpeed Standard or Coated Bearings. Both feature super smooth, super-round CeramicSpeed Balls contained in hardened-steel races. The Coated version has a metallic coating laid onto the races, making it even smoother and harder, resulting in lower drag and longer life. -BB90 is simple and light. The standard is designed to work with 24mm spindles. The bearings work with Shimano and other 24mm cranks, like FSA. - The CeramicSpeed Standard Bearings last at least 3 times longer than other bearings. That's thanks to hardened-steel races and CeramicSpeed Balls that are 100% smoother & 15% harder than the ceramic competition. These bearings have a frictional drag of 0.3-0.4 watts per set, which represents an average 75% drag reduction compared to stock BBs. - The CeramicSpeed Coated Bearings reduce drag by 50% compared to Standard Bearings and an improvement in bearing life of 60%. In The Box: - 2 BB90 bearings - 2 seals - 2 dust covers with integrated spacers - 10ml syringe of All Round Grease - Sticker Sheet

BSA is another way of stating English threading. The initialization comes from Birmingham Small Arms, which made bicycles. English threading on road bikes mean a 68mm wide, 34mm inside diameter shell with reverse threading on the drive side. It's the most common threaded standard employed today. This kit works with 24mm diameter cranks, found on cranks from Shimano, FSA, Rotor, and others. Choose between two bearings for the cups. Standard Bearings have low drag thanks to hardened-steel races and our Ceramic balls. Coated Bearings have those same balls installed on coated, hardened-steel races for longer life and less bearing drag. 24mm spindles easily fit through the shell and allow for large bearings to be employed in the outside cups. Put more of your energy into forward motion by reducing frictional drag wherever you can. CeramicSpeed Standard Bearings typically have frictional drag of 0.3-0.4 watts per set. That's in the range of a 75% drag reduction compared to standard bottom brackets. CeramicSpeed balls are 100% smoother and 15% harder than ceramic competition. The bearings last at least 3x longer than other bearings. In The Box: - 2 threaded cups with bearings - 2 dust covers with built-in spacers - Spacer tube - 10mm syringe of All Round Grease - Sticker sheet

Italian-threaded bottom bracket shells are typically found on Italian-brand road bikes. The shell measures 70mm wide and has a 35mm inner diameter. This kit has all the pieces necessary to install 24mm diameter cranks, such as those from Shimano, FSA, and others into an ITA shell. CeramicSpeed bearings are pressed into threaded cups, then those cups are threaded into the frame. You choose whether you want yours equipped with Standard or Coated Bearings. Super-round, super-smooth CeramicSpeed balls rotate in hardened-steel races in both. The Coated version has a metallic coating laid onto the races, making them even harder and smoother, resulting in longer life and lower drag. ITA BBs, thanks to the popularity of Italian road bike design, still have a following. The drive-side cup needs to be properly secured, but once that's done, the system is excellent. 24mm cranks work better when mated to our bearings. To make your bike as efficient as possible, you must reduce mechanical drag. Bottom brackets have a measurable effect on speed. CeramicSpeed balls are 100% smoother and 15% harder than the ceramic competition. They run on smoother races, too. That means our Standard Bearing BBs have 75% less drag compared to typical bottom brackets. And, the bearings last at least 3x longer than other bearings. These bearings come packed with All Round Grease. If you want less drag and are riding in cleaner environs, install lowest drag TT and Track Grease. If you're riding in wet conditions, more durable LongLife Grease can be put in. In The Box: - 2 threaded cups with bearings - 2 dust covers with built-in spacers - Spacer tube - 10ml syringe of All Round grease - Sticker sheet

This bottom bracket is perfect for when you have a PF30, BBright, or 386EVO shell frame and want to install a crank with a 30mm spindle into the frame. All these frame standards have a 46mm inner diameter and smooth insides, though the widths vary from 68mm to 86mm. This bottom bracket features nearly zero loss of power due to friction, thanks to the CeramicSpeed's incredibly efficient bearings. Choose either our Standard or Coated Bearings—both have super-round, super-smooth CeramicSpeed balls rolling on hardened-steel races. The Coated version has a metallic coating laid onto the races, making them even harder and smoother and resulting in longer life and lower drag. They come installed in cups. 30mm spindles on cranks are increasingly popular because of the high stiffness and low weight. 46mm inner diameter bottom brackets are popular for the freedom they offer designers in building frames. Because of the variety of widths, the cups here extend into the shell and come with a telescoping spacer tube to further seal and stiffen the system. The bottom bracket is already stiff thanks to hard ceramic bearings and hardened-steel races. Thanks to CeramicSpeed, it also generates nearly zero drag. Standard Bearings typically have frictional drag of 0.3-0.4 watts per set. That's in the range of a 75% drag reduction versus conventional BBs. The bearings also last at least 3x longer than other bearings. You can change the grease to fine-tune your BB's performance characteristics. TT and Track, All Round, and LongLife are greases CeramicSpeed designed. The first has the least drag, while the last is the most durable. All Round, in the middle, comes standard in road bearings. In The Box - 2 cups with bearings installed - 2 1mm spacers - 2 0.5mm spacers - 2 dust covers - O-ring - Spacer tube - 10ml All Round Grease - Sticker sheet

The new SRAM DUB crank standard, built on a 28.99mm spindle, allows for a more contamination-resistant BB design while retaining the ultra-efficient & long-lasting qualities CeramicSpeed Bottom Brackets are known for. With an integrated dust cover for all models, the snug & secure fit not only fully protects the face of the bearing, but also delivers exceptional performance without any sacrifices. CeramicSpeed hand-built bearings carry the load from crank to frame with unparalleled durability & efficiency. The SRAM DUB crank spindle requires the bearing contact points to be in a set and designated width, and all CeramicSpeed bottom Bracket options perfectly match the bearing placement on the crank spindle with the required frame interface for nearly any model of bike. Without the use of unnecessary adapters or spacers, a quiet & stable platform is ensured throughout the life of the product. The BBright for SRAM DUB Road comes in two versions. The first is our low drag, long life Standard Bearing with hardened-steel races and our super-round CeramicSpeed balls. The second is our Coated Bearing, which uses those same balls installed on coated, hardened-steel races for longer life and less bearing drag. Compatible with: - Frame: BBright - Opening diameter: 46mm - Shell width: 79mm In the box: - 2 cups with CeramicSpeed Bearings installed - 2 dust covers - Spacer-tube - 4 x 1mm spacers - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet

The new SRAM DUB crank standard, built on a 28.99mm spindle, allows for a more contamination-resistant BB design while retaining the ultra-efficient & long-lasting qualities CeramicSpeed Bottom Brackets are known for. With an integrated dust cover for all models, the snug & secure fit not only fully protects the face of the bearing, but also delivers exceptional performance without any sacrifices. CeramicSpeed hand-built bearings carry the load from crank to frame with unparalleled durability & efficiency. The SRAM DUB crank spindle requires the bearing contact points to be in a set and designated width, and all CeramicSpeed bottom Bracket options perfectly match the bearing placement on the crank spindle with the required frame interface for nearly any model of bike. Without the use of unnecessary adapters or spacers, a quiet & stable platform is ensured throughout the life of the product. The EVO386 for SRAM DUB Road comes in two versions. The first version uses our low drag, long life Standard Bearing with hardened-steel races and our super-round CeramicSpeed balls. The second version uses our Coated Bearing, which uses those same balls installed on coated, hardened-steel races for longer life and less bearing drag. Compatible with: - Frame: EVO386 - Opening diameter: 46mm - Shell width: 86.5mm In the box: - 2 cups with CeramicSpeed Bearings installed - 2 dust covers - Spacer-tube - 4 x 1mm spacers - 2 x 3mm spacers - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet

The new SRAM DUB crank standard, built on a 28.99mm spindle, allows for a more contamination-resistant BB design, while retaining the ultra-efficient & long-lasting qualities CeramicSpeed Bottom Brackets are known for. With an integrated dust cover for all models, the snug & secure fit not only fully protects the face of the bearing, but also delivers exceptional performance without any sacrifices. CeramicSpeed hand-built bearings carry the load from crank to frame with unparalleled durability & efficiency. The SRAM DUB crank spindle requires the bearing contact points to be in a set and designated width, and all CeramicSpeed bottom Bracket options perfectly match the bearing placement on the crank spindle with the required frame interface for nearly any model of bike. Without the use of unnecessary adapters or spacers, a quiet & stable platform is ensured throughout the life of the product. The ITA for SRAM DUB Road comes in two bearing options. The first option is our low drag, long life Standard Bearing with hardened-steel races and our super-round CeramicSpeed balls. The second option is our Coated Bearing, which uses those same balls installed on coated, hardened-steel races for longer life and less bearing drag. Compatible with: - Frame: Italian BB - Opening diameter: Threaded - Shell width: 70mm In the box: - 2 cups with CeramicSpeed Bearings installed - 2 dust covers - 4 x 1mm spacers - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet - Spacer tube

The new SRAM DUB crank standard, built on a 28.99mm spindle, allows for a more contamination-resistant BB design, while retaining the ultra-efficient & long-lasting qualities CeramicSpeed Bottom Brackets are known for. With an integrated dust cover for all models, the snug & secure fit not only fully protects the face of the bearing, but also delivers exceptional performance without any sacrifices. CeramicSpeed hand-built bearings carry the load from crank to frame with unparalleled durability & efficiency. The SRAM DUB crank spindle requires the bearing contact points to be in a set and designated width, and all CeramicSpeed bottom Bracket options perfectly match the bearing placement on the crank spindle with the required frame interface for nearly any model of bike. Without the use of unnecessary adapters or spacers, a quiet & stable platform is ensured throughout the life of the product. The PF30A for SRAM DUB Road comes in two versions. The first version uses our low-drag, long-life Standard Bearing with hardened-steel races and our super-round CeramicSpeed balls. The second version uses our Coated Bearing, which uses those same balls installed on coated, hardened-steel races for longer life and less bearing drag. Compatible with: - Frame: PF30A - Opening diameter: 46mm - Shell width: 73mm In the box: - 2 cups with CeramicSpeed Bearings installed - 2 dust covers - Spacer-tube - 4 x 1mm spacers - 2 x 3mm spacers - 10 ml syringe of CeramicSpeed All Round Grease - Sticker sheet

The Hellbender 110 Bottom Bracket provides an incredible mix of performance and longevity through the inclusion of Enduro XD-15 ceramic bearings. These bearings feature nitrogen-infused stainless steel races that will not rust or corrode paired with Silicon Nitride ceramic balls. - BB30 for 30mm Spindles - Lifetime Guarantee

The Hellbender 110 Bottom Bracket provides an incredible mix of performance and longevity through the inclusion of Enduro XD-15 ceramic bearings. These bearings feature nitrogen infused stainless steel races that will not rust or corrode paired with Silicon Nitride ceramic balls. - Enduro XD-15 ceramic ball bearings are made from pure silicon nitride material with extreme high density and uniform compaction - The race material is an advanced stainless alloy that is nitrogen infused and will not rust or corrode - Dual stage anodize black and gold machined aluminum bottom bracket cups - Kluber NBU52 grease runs better and smoother with time and is highly resistant to being washed out - Designed for use with 30mm spindles

The Wheels Mfg BB30 Outboard bottom bracket will give you all of the same benefits as their other Outboard style BBs. The two machined aluminum cups thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life, and simplifying maintenance. This means no more creaking, smoother operation, longer bearing life, and really quick bearing replacement. Specifically designed for installing 24mm spindle diameter cranks (Shimano, FSA, Etc.) in BB30 frames without the need for adapters. - Bearings: Enduro ZERØ Ceramic - Color: Red - Bottom Bracket/Frame Interface: BB30, Specialized Alloy OSBB - Bottom Bracket Shell Width (mm): 68mm - 73mm - Bottom Bracket Shell I.D.: 42mm - Crank Spindle Type: Shimano Hollowtech II, FSA MegaExo, RaceFace EXI - Crank Spindle Diameter: 24mm - Weight: 122g

PF30 Threaded bottom bracket features two machined aluminum cups that thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life, and simplifying maintenance. This means no more creaking, smoother operation, longer bearing life, and really quick bearing replacement. Directly replaces all OEM PF30 bottom brackets. Note: Use only bottom bracket tools compatible with 16-notch, 48.5mm outer diameter cups. - Bearings: Enduro ZERØ Ceramic Hybrid - Color: Black - Bottom Bracket/Frame Interface: PF30, Specialized Carbon OSBB, BBRight™ Press Fit - Bottom Bracket Shell Width (mm): 61mm to 79mm - Bottom Bracket Shell I.D.: 46mm - Crank Spindle Type: BB30 - Crank Spindle Diameter: 30mm - Weight: 106g

- Ceramic bottom bracket for DUB spindle cranks Specs: - BB Shell Type: BB30 - BB Shell Width: 68/73mm - BB Bearing: Ceramic - Crank Spindle Diameter: 28.99mm - Interface: DUB - Cup Diameter: 42mm

- Ceramic bottom bracket for DUB spindle cranks Specs: - BB Shell Type: PF30 - BB Shell Width: 68/73mm - BB Bearing: Ceramic - Crank Spindle Diameter: 28.99mm - Interface: DUB - Cup Diameter: 46mm

- Ceramic bottom bracket for DUB spindle cranks Specs: - BB Shell Type: BB92 - BB Shell Width: 89/92mm - BB Bearing: Ceramic - Crank Spindle Diameter: 28.99mm - Interface: DUB - Cup Diameter: 41mm

The Wheels Mfg PF30 Outboard bottom bracket will give you all of the same benefits as their well-loved Outboard style BBs. The two machined aluminum cups thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life, and simplifying maintenance. This means no more creaking, smoother operation, longer bearing life, and really quick bearing replacement. Specifically designed for installing 24mm spindle diameter cranks (Shimano, FSA, Etc.) in PF30 frames without the need for adapters. - Bearings: Enduro ZERØ Ceramic - Color: Red - Bottom Bracket/Frame Interface: PF30, Specialized Carbon OSBB - Bottom Bracket Shell Width (mm): 68mm - 73mm - Bottom Bracket Shell I.D.: 46mm - Crank Spindle Type: Shimano Hollowtech II, FSA MegaExo, RaceFace EXI - Crank Spindle Diameter: 24mm - Weight: 156g

Expand your choice of cranks for use in BB86/BB92/BB91/BB71-41/BB107 frames. Replace your bottom bracket with these dual-row flanged bearings and run 30mm spindle cranks (FSA BB386EVO, Rotor 3d+, RaceFace Next SL, e.thirteen) cranks in your frame. These bearings fit directly in frames with 41mm ID smooth bore bottom bracket shells.You must use 30mm spindle cranksets with spindle lengths longer than 104mm. - Bearings: Enduro Dual-Row ABEC-3 - Dimensions: 41mm x 30mm (42mm flange OD) - Color: silver - Bottom Bracket/Frame Interface: BB86, BB92, BB91, BB71-41, BB107/104 - Bottom Bracket Shell Width (mm): 86.5mm - 107mm - Bottom Bracket Shell I.D.: 41mm - Crank Spindle Type: BB386EVO, BB30 longer than 104mm - Crank Spindle Diameter: 30mm - Weight: 89g

Expand your choice of cranks for use in frames with 41mm ID shells. Replace your bottom bracket with these dual-row flanged bearings and run 29mm spindle (SRAM DUB) cranks in your frame. These bearings fit directly in frames with 41mm ID bottom bracket shells. Crankset spindle length must be longer than 104mm when used in a 86.5mm wide BB shell. - Bearings: Enduro Dual-Row ABEC-3 - Color: Silver - Bottom Bracket/Frame Interface: BB86, BB92, PF90, BB104/107, PF121, PF132 - Bottom Bracket Shell Width: 86.5mm - 132mm - Bottom Bracket Shell I.D.: 41mm - Flange OD: 42mm - Crank Spindle Diameter: 29mm (DUB) - Over Bearing Width: 92mm in 86.5mm wide shell (Dimensions include supplied silicone dust shields) - Weight: 90g Complete kit for one frame includes: - (2) Enduro BB86 to 30MM Dual-Row ABEC-3 Bearing - (2) 0.5mm crank spacer - (2) 1.0mm crank spacer - (2) 5.0mm crank spacer - (2) Dust seals

- Road sets include bearings, shields, c-clips and wavy washer for bearing retention/tension - Mountain sets include bearings, shields, c-clips and spacer - Choose ceramic or stainless steel options

Convert your PF30 frame to a single-speed setup with our simple to use bottom bracket. Enduro Angular Contact sealed bearings. Double lip seals on all bearings with high fill rate top quality grease for maximum durability. Machined aluminum cups are superior in function and durability to plastic. Fully serviceable. - Bearings: Enduro Angular Contact - Color: Red - Bottom Bracket/Frame Interface: PF30, Specialized Carbon OSBB - Bottom Bracket Shell Width (mm): 68mm - 73mm - Bottom Bracket Shell I.D.: 46mm - Chain Adjustment: 12mm - Crank Spindle Type: GXP (SRAM, Truvativ, etc.) - Crank Spindle Diameter: 22/24mm - Weight: 194g

Convert your PF30 frame to a single-speed setup with our simple to use bottom bracket. Enduro Angular Contact sealed bearings. Double lip seals on all bearings with high fill rate top quality grease for maximum durability. Machined aluminum cups are superior in function and durability to plastic. Fully serviceable. - Bearings: Enduro Angular Contact - Color: Red - Bottom Bracket/Frame Interface: PF30, Specialized Carbon OSBB - Bottom Bracket Shell Width (mm): 68mm - 73mm - Bottom Bracket Shell I.D.: 46mm - Chain Adjustment: 12mm - Crank Spindle Type: Shimano Hollowtech II, FSA MegaExo, RaceFace EXI - Crank Spindle Diameter: 24mm - Weight: 182g

The two machined aluminum cups thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life and simplifying maintenance. Enjoy smooth operation, fast bearing replacement, and no more creaking. - Bearings: Enduro Angular Contact (22/24mm SRAM non-drive-side bearing: ABEC-3) - Color: Black - Bottom Bracket/Frame Interface: Cannondale BB30A - Bottom Bracket Shell Width: 73mm - Bottom Bracket Shell I.D.: 42mm - Over Bearing Width: 91mm in 73mm wide shell (dimensions include supplied silicone dust shields) - Tool Pattern: 44mm x 16 notch

The two machined aluminum cups thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life and simplifying maintenance. Enjoy smooth operation, fast bearing replacement, and no more creaking. - Bearings: Enduro Angular Contact - Color: Black - Bottom Bracket/Frame Interface: Cannondale BB30A - Bottom Bracket Shell Width: 73mm - Bottom Bracket Shell I.D: 42mm - Over Bearing Width: 91mm in 73mm wide shell (dimensions include supplied silicone dust shields) - Tool Pattern: 44mm x 16 notch

PF30 Threaded bottom bracket features two machined aluminum cups that thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life, and simplifying maintenance. This means no more creaking, smoother operation, longer bearing life, and really quick bearing replacement. Directly replaces all OEM PF30 bottom brackets. Note: Use only bottom bracket tools compatible with 16-notch, 48.5mm outer diameter cups. - Bearings: Enduro ABEC-3 - Color: Black - Bottom Bracket/Frame Interface: PF30, Specialized Carbon OSBB, BBRight™ Press Fit - Bottom Bracket Shell Width (mm): 61mm to 79mm - Bottom Bracket Shell I.D.: 46mm - Crank Spindle Type: BB30 - Crank Spindle Diameter: 30mm - Weight: 115g

Specifically designed for installing 24.00mm spindle diameter cranks (Shimano, Etc.) in Cannondale PF30A (46mm ID, 73mm wide asymmetrical BB shell) frames without the need for any adapters. The two machined aluminum cups thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life, and simplifying maintenance. This means no more creaking, smoother operation, longer bearing life, and really quick bearing replacement. - Bearings: Enduro Angular Contact - Color: Black - Bottom Bracket/Frame Interface: Cannondale PF30A - Bottom Bracket Shell Width: 73mm - Bottom Bracket Shell I.D.: 46mm - Over Bearing Width: 91mm in 73mm wide shell (dimensions include supplied silicone dust shields) - Tool Pattern: 44mm x 16 notch Note: FSA MegaExo spindles can be between 24.00mm and 24.07mm in diameter. If your FSA spindle is 24.07mm, this BB will not work! Please purchase Wheels Mfg. FSA 24.07x37 ceramic hybrid bearings separately

With precision sealed bearings and cold-forged, aluminum CNC machined cups, the Box One™ Titanium Square Taper bottom brackets are the best option for young BMX racers and other users. It is a three-piece crank in search of performance gains and weight savings. They have hollow, custom titanium-nitride-coated titanium spindles and carbon fiber center seals, helping keep the weight down between 185 and 190 grams (well below that of other square taper bottom brackets on the market). Other features include cups that are anodized black with anodized gold inner seals and a JIS tapered spindle that comes in either 108 or 113 millimeters. Weight Limit: 115kg (253 lbs) with limitations as per Category 2 of EN 16054:2012 Standard Features: - Precision Abec-5 Sealed Bearings - Lightweight Non-Structural Carbon Components - Extra Rigid Titanium Spindle Compatibility: - Box Five Square Taper Crankset Specs: Process: CNC-Machined Cups Material: - Spindle: Titanium - Cups: Alloy - Sleeve: Carbon Fiber Finish: Titanium Nitride Coated Spindle Type: JIS Square Taper Spindle Length: 108mm or 113mm Shell Width: 68mm Thread: 1.37" x 24 TPI Compatibility: BSA Threaded Weight [108-113] (+/- 5%): 199-204 g / 7-7.2 oz

The Problem Solvers Bushnell Eccentric Bottom Bracket is the industry leading design for chain tension adjustment on tandem and dedicated single speed bikes equipped with eccentric bottom bracket shells. The classic version features full-body, aluminum construction across the shell for maximum surface area friction and additional value. The Bushnell Fat Bike Eccentric Bottom Bracket is designed for the 100mm shells in most fat bikes. - Accepts English threaded bottom bracket cups - Classic, full-body design - Diameter of part - 2.118 inches (53.78mm) - Fits BB shells from 53.8 ~ 54mm I.D. without shim - Fits BB shells up to 100mm width

• Fits BB92, BB89.5 and BB86.5 frames • Easily serviced, replaceable sealed bearings and external labyrinth seal • Cups pressed in and held in place by a screw in centre tube stopping any movement or play usually found in press-fit frames • Compatible with any 24mm axle cranks • Requires Hope PressFit BB tool for installation (sold separately) • Available with either stainless steel or ceramic bearings

Threaded Angular Contact BB for 386EVO frames (86.5mm shell width, 46mm shell ID). Machined cups thread together for stability, increased bearing life, and simple installation and maintenance. No more creaking. Smooth operation. Fast bearing replacement. - Bearings: Enduro Angular Contact - Color: Black - Bottom Bracket/Frame Interface: BB386EVO - Bottom Bracket Shell Width (mm): 86.5mm - Bottom Bracket Shell I.D.: 46mm - Crank Spindle Type: BB30 - Crank Spindle Diameter: 30mm - Weight: 124g - Packaged for retail display - Will accept 24mm and 24/22mm cranksets using Wheels Mfg. 386EVO BB / Crank Adapters

Thread-together BB for 386EVO frames and 22/24mm diameter spindle cranks. Machined aluminum cups thread together for stability, increased bearing life, and simple installation and maintenance. Enjoy smooth operation, fast bearing replacement, and no more creaking. - Drive Side Bearing: Enduro Angular Contact - Non-Drive Side Bearing: Enduro ABEC-3 - Color: Black - Bottom Bracket/Frame Interface: BB386EVO, BB392EVO - Bottom Bracket Shell Width (mm): 86mm – 92mm - Bottom Bracket Shell I.D.: 46mm - Crank Spindle Diameter: 22/24mm stepped - Over Bearing Width: 91.8mm in 86.5mm wide shell (dimensions include supplied silicone dust shields) - Weight: 145g

Thread together BB for 386EVO frames and 24mm diameter spindle cranks. Machined aluminum cups thread together for stability, increased bearing life, and simple installation and maintenance. Enjoy smooth operation, fast bearing replacement, and no more creaking. - Bearings: Enduro Angular Contact - Color: Black - Bottom Bracket/Frame Interface: BB386EVO, BB392EVO - Bottom Bracket Shell Width: 86.6mm - Bottom Bracket Shell I.D.: 46mm - Crank Spindle Diameter: 24mm - Over Bearing Width: 91.5mm in 86.5mm wide shell (dimensions include supplied silicone dust shields) - Weight: 133g

The Wheels Mfg BB30 Outboard bottom bracket will give you all of the same benefits as their other Outboard style BBs. The two machined aluminum cups thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life, and simplifying maintenance. This means no more creaking, smoother operation, longer bearing life, and really quick bearing replacement. Specifically designed for installing 24mm spindle diameter cranks (Shimano, FSA, Etc.) in BB30 frames without the need for adapters. - Bearings: Enduro Angular Contact - Color: Red - Bottom Bracket/Frame Interface: BB30, Specialized Alloy OSBB - Bottom Bracket Shell Width (mm): 68mm - 73mm - Bottom Bracket Shell I.D.: 42mm - Crank Spindle Type: Shimano Hollowtech II, FSA MegaExo, RaceFace EXI - Crank Spindle Diameter: 24mm - Weight: 127g

Wheels Mfg BB86/92 thread together bottom bracket for use with 24mm spindle diameter cranksets. The two machined aluminum cups thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life, and simplifying maintenance. This means no more creaking, smoother operation, longer bearing life, and really quick bearing replacement. Note: Use only bottom bracket tools compatible with 16-notch, 48.5mm outer diameter cups. - Bearings: Enduro Angular Contact - Color: Black - Bottom Bracket/Frame Interface: BB86, BB92 - Bottom Bracket Shell Width (mm): 86mm, 92mm, 89.5mm - Bottom Bracket Shell I.D.: 41mm - Crank Spindle Type: Shimano Hollowtech II, FSA MegaExo, RaceFace EXI - Crank Spindle Diameter: 24mm - Weight: 106g

BBRight™ Outboard bottom bracket for use with 24mm spindle diameter cranksets. The two machined aluminum cups thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life, and simplifying maintenance. This means no more creaking, smoother operation, longer bearing life, and really quick bearing replacement. - Bearings: Enduro Angular Contact - Color: Black - Bottom Bracket/Frame Interface: BBRight™ Press Fit - Bottom Bracket Shell Width (mm): 79mm - Bottom Bracket Shell I.D.: 46mm - Crank Spindle Type: Shimano Hollowtech II, FSA MegaExo, RaceFace EXI - Crank Spindle Diameter: 24mm - Weight: 146g

The Wheels Mfg PF30 Outboard bottom bracket will give you all of the same benefits as their well-loved Outboard style BBs. The two machined aluminum cups thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life, and simplifying maintenance. This means no more creaking, smoother operation, longer bearing life, and really quick bearing replacement. Specifically designed for installing 24mm spindle diameter cranks (Shimano, FSA, Etc.) in PF30 frames without the need for adapters. - Bearings: Enduro Angular Contact - Color: Red - Bottom Bracket/Frame Interface: PF30, Specialized Carbon OSBB - Bottom Bracket Shell Width (mm): 68mm - 73mm - Bottom Bracket Shell I.D.: 46mm - Crank Spindle Type: Shimano Hollowtech II, FSA MegaExo, RaceFace EXI - Crank Spindle Diameter: 24mm - Weight: 158g

By popular demand, Wheels Mfg. added this PF30 Outboard Bearing BB for use with 30mm spindle cranksets when used in PF30 frames. The two machined aluminum cups thread together keeping the bottom bracket stable in the frame, increasing bearing life and simplifying maintenance. This means smooth operation, fast bearing replacement, and no more creaking. Note: Spindle length must be 103mm or longer when used in a 68mm wide shell; 108mm or longer when used in a 73mm wide shell. - Bearings: Enduro Angular Contact - Color: Black - Bottom Bracket/Frame Interface: PF30, Specialized Carbon OSBB - Bottom Bracket Shell Width: 61mm – 83mm (Specialized Carbon OSBB with 61mm shell width will need additional 3.5mm cup spacers, sold separately) - Bottom Bracket Shell I.D.: 46mm - Over Bearing Width: 89mm in 68mm wide shell (dimensions include supplied silicone dust shields) - Crank Spindle Diameter: 30mm - Tool Pattern: 48.5mm x 16 notch - Weight: 151g

PF30 Threaded bottom bracket features two machined aluminum cups that thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life, and simplifying maintenance. This means no more creaking, smoother operation, longer bearing life, and really quick bearing replacement. Directly replaces all OEM PF30 bottom brackets. Note: Use only bottom bracket tools compatible with 16-notch, 48.5mm outer diameter cups. - Bearings: Enduro Angular Contact - Color: Black - Bottom Bracket/Frame Interface: PF30, Specialized Carbon OSBB, BBRight™ Press Fit - Bottom Bracket Shell Width (mm): 61mm to 79mm - Bottom Bracket Shell I.D.: 46mm - Crank Spindle Type: BB30 - Crank Spindle Diameter: 30mm - Weight: 114g

The two machined aluminum cups thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life, and simplifying maintenance. This means no more creaking, smoother operation, longer bearing life, and really quick bearing replacement. Specifically designed for installing SRAM DUB Compatible cranks in Cannondale PF30A (46mm ID, 73mm wide asymmetrical BB shell) frames. Bottom Bracket Includes: - BB Cups with bearings - 2x - Silicone dust seals - 2x - 0.5mm crank spindle spacers - 2x - 1.0mm crank spindle spacers - 1x - 2.5mm crank spindle spacer - Bearings: Enduro ABEC-3 - Bottom Bracket/Frame Interface: Cannondale PF30A - Bottom Bracket Shell Width: 73mm Asymmetrical - Bottom Bracket Shell I.D.: 46mm - Over Bearing Width: 91mm in 73mm wide shell - Over Bearing Width Dimensions include supplied silicone dust shields. - Crank Spindle Diameter: 29mm - Tool Pattern: 48.5mm x 16 notch - Weight: 158g

Specifically designed for installing 22/24mm spindle diameter cranks (SRAM) in Cannondale PF30A (46mm ID, 73mm wide asymmetrical BB shell) frames without the need for any adapters. The two machined aluminum cups thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life, and simplifying maintenance. Enjoy smooth operation, fast bearing replacement, and no more creaking. - Bearings: ABEC-3 - Color: Black - Bottom Bracket/Frame Interface: Cannondale PF30A - Bottom Bracket Shell Width: 73mm - Bottom Bracket Shell I.D.: 46mm - Over Bearing Width: 91mm in 73mm wide shell (dimensions include supplied silicone dust shields) - Tool Pattern: 44mm x 16 notch

Specifically designed for installing 24.00mm spindle diameter cranks (Shimano, etc.) in Cannondale PF30A (46mm ID, 73mm wide asymmetrical BB shell) frames without the need for any adapters. The two machined aluminum cups thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life, and simplifying maintenance. This means smooth operation, fast bearing replacement, and no more creaking. - Bearings: ABEC-3 - Color: Black - Bottom Bracket/Frame Interface: Cannondale PF30A - Bottom Bracket Shell Width: 73mm - Bottom Bracket Shell I.D.: 46mm - Over Bearing Width: 91mm in 73mm wide shell (dimensions include supplied silicone dust shields) - Tool Pattern: 44mm x 16 notch Note: FSA MegaExo spindles can be between 24.00mm and 24.07mm in diameter. If your FSA spindle is 24.07mm, this BB will not work! Please purchase Wheels Mfg. FSA 24.07x37 ceramic hybrid bearings separately.

The two machined aluminum cups thread together ensuring the bottom bracket remains stable in the frame, increasing bearing life, and simplifying maintenance. This means no more creaking, smoother operation, longer bearing life, and really quick bearing replacement. Specifically designed for installing 30mm spindle cranks in Cannondale PF30A (46mm ID, 73mm wide asymmetrical BB shell) frames. Bottom Bracket Includes: - BB Cups with bearings - 2x - Silicone dust seals - 2x - 0.5mm crank spindle spacers - 2x - 1.0mm crank spindle spacers - Bearings: Enduro ABEC-3 - Bottom Bracket/Frame Interface: Cannondale PF30A - Bottom Bracket Shell Width: 73mm Asymmetrical - Bottom Bracket Shell I.D.: 46mm - Over Bearing Width: 91mm in 73mm wide shell - Crank Spindle Diameter: 30mm - Tool Pattern: 48.5mm x 16 notch - Weight: 158g

T47 threaded BB cups for running 22/24mm spindle (SRAM) cranks in T47 frames. Cups have internal bearings and are typically used in BB shells with widths wider than 73mm. Machined aluminum cups thread together directly into a T47 BB shell. Bearings are easily serviced or replaced. Includes sleeve to fit between cups for added protection from dirt and grime, and also keeps your internal wires and hoses from rubbing on the crank spindle. T47 BB cups are similar to standard BSA threaded cups in that the drive side cup is left-hand thread and the non-drive side cup is right-hand thread. Use a quality grease when installing in steel or aluminum BB shells, or a titanium-compatible anti-seize compound in titanium BB shells. - Bearings: Enduro Angular Contact (non-drive-side bearing: ABEC-3) - Bottom Bracket/Frame Interface: T47 - Bottom Bracket Shell Width: 68mm – 132mm - Bottom Bracket Shell I.D.: 47x1.0mm Threaded - Over Bearing Width: 91.7mm in 86.5mm wide shell (dimensions include supplied silicone dust shields) - Tool Pattern: 48.5mm x 16-notch