BMX

Black Label's 6061 Sprocket is machined from 1/4-inch thick 6061 aluminum for awesome strength and durability. An adapter for 19mm axles is included.

Ride Black Label's Front Wheel in the park, street or at the dirt jumps. This sweet 20-inch wheel is strong and ready for action thanks to a 36-spoke build, a fine sealed-bearing Black Label hub with a 3/8-inch axle and a tough, light aluminum rim.

Black Label's Mid BB Set includes bearings, washers, a center spacer, and cones. It's for use with 19mm crank axles.

Ride Black Label's Moto Front Wheel in the park, street or at the dirt jumps. This standard 20-inch wheel is strong and ready for action thanks to a 36-spoke build, a quality hub with a 3/8-inch axle and a tough, light aluminum rim.

Ride Black Label's Moto Rear Wheel w/Driver in the park, street or at the dirt jumps. This sweet 20-inch wheel is built for action with 36 spokes, a tough, light aluminum rim and a quality hub with a 14mm axle and a 9T one-piece driver.

Roll on Black Label's Rear Wheel w/Driver in the park, street or at the dirt jumps. This sweet 20-inch wheel is built for action with 36 spokes, a tough, light aluminum rim and a sealed-bearing Black Label aluminum cassette hub with a 9T Driver and 14mm axle.

Rolling on 18s? Upgrade to Black Label's Vise 18-inch Rear Wheel. It's strong thanks to a 36-spoke build, a quality hub and a tough and light aluminum rim. It's available in a 9T driver and 14mm axle model or Microdrive with a 3/8-inch axle setup.

- Upper cables measured from brake lever to detangler top plate - Lower cables are measured from detangler to cable stop/London mod - Includes adjusters compatible with most detangler styles - Use: Lower - Length: Dual Cable - Diameter: 1.5mm

- Upper cables measured from brake lever to detangler top plate - Lower cables are measured from detangler to cable stop/London mod - Includes adjusters compatible with most detangler styles - Use: Lower - Length: Fits most - Diameter: 1.5mm

- Upper cables measured from brake lever to detangler top plate - Lower cables are measured from detangler to cable stop/London mod - Includes adjusters compatible with most detangler styles - Use: Upper - Length: 7.5 – 9.5-inch - Diameter: 1.5mm

- Upper cables measured from brake lever to detangler top plate - Lower cables are measured from detangler to cable stop/London mod - Includes adjusters compatible with most detangler styles - Use: Upper - Length: 11 - 12.5" - Diameter: 1.5mm

- Upper cables measured from brake lever to detangler top plate - Lower cables are measured from detangler to cable stop/London mod - Includes adjusters compatible with most detangler styles - Use: Lower - Length: X-Long - Diameter: 1.5mm

- Precise fit and smooth function - Great cable travel range - Shielded cables for durability - Includes upper and lower cables - Use: 1-1/8" BMX

- Threads onto 3/8" axles - Double-sided - Oversized - Alloy - Length: 3" / 74mm - Width: .94" / 24mm - Sold as a pair

- CNC machined 6061-T6 aluminum chain tensioners - Compatible with 3/8 inch and 10mm axles - Single bolt operation makes tensioning a simple task - Material: 6061AL

- Steel - Threads onto 3/8" axle - Knurled & grooved - Diameter: 33mm - Sold in pairs

- 4130 chromoly axle pegs with 3 position anti-rotation set screw - Designed for use with 14mm or 3/8" axles (with adapter) - 4130 chromoly offers a durable, long lasting peg with a smooth grind - 3 set screw positions extend the life the of the peg - Axle: 14mm / 3/8" - Diameter: 35mm - Material: Chromoly - Sold in pairs

- Allows the use of wheels with 3/8" axles to be used with frames or pegs requiring 14mm axles - Durable chromoly construction - Sold in pairs

8 spline BMX bottom bracket Spindle with bolts. - Diameter: 19mm - Crank arm Interface: 8-spline - Length: 150mm - Bolts included

- Forged alloy construction - Double bolt centering design - Oversize 6mm hex bolts

- Super hardened nylon construction - 40mm diameter, 100mm length - Special insert fits 3/8" or 14mm axles - 90g (pair)

- Super hardened Cr-Mo/Nylon construction - 40 x 100mm - Special insert fits 3/8" or 14mm axles - Diameter: 40mm - 320g (pair) - Material: Chromoly Core w/Nylon Sleeve - Sold in pairs

The MK 4 version continues the GLAND’s heritage, but in a smaller and sleeker overall size which should appease many riders. The images beside show the top, profile, and under side of each guard.

The new Gsport Uniguard is a simple, inexpensive functional guard that eliminates the need to spread the dropouts. It’s made from Heat-Treated Cr-Mo Steel and is LHD and RHD compatible as well as Drive and Non-Drive compatible. All bases covered. Available in 14mm or 3/8?.

The Gyro G3 upper top plate is designed for use with the G3 detangler.

- Sold in pairs - Allen wrench included

Odyssey's custom-designed Par Ends come standard with all of their grips. Its special plastic composite will not shatter like cheap bar ends do, and they’re very lightweight. The Par End is a combination of the over-the-bar-style cap and the inside-the-bar-style to prevent the inner portion from blowing out like it does on ordinary press-fit bar ends. Comes stock on all of Odyssey's grips.

When you can’t even see a part, you might forget about it, but it doesn’t mean its not important. Flat tires are probably the most common bicycle failures. Many times, flats are caused by the rims, specifically the lack of protection from the rims' sharp edges. Good rim strips didn’t exist for BMX rims. They work well and improve the function of any 20 inch rim. If you forget about them, that means they are doing their job.

The Graduate sleeve is the replacement sleeve for the Graduate peg that's made from long lasting, fast sliding plastic. - Sold singly

The M2 lever works with a single cable or Odyssey's dual cable system. - Improved braking power for Gyro users - Left/Right hand compatible

One of the most important goals that Odyssey had when they sat down to work on new braking designs was to make the whole system easier to install (and remove) without sacrificing performance. They also wanted to be sure that every component would be very affordable too. The Ghost Pad addresses the hassles of brake pad installation by eliminating the traditional dome shaped washers used for toe-in. The pad improves stiffness by building the toe-in into the pad shape and utilizing a solid extruded aluminum frame at its core. The Ghost Pad’s assembly consists of simply lining it up with the rim and tightening down an M6 female bolt. Comes stock on the Springfield brake. SPECS Hardware: - In-bound bolt, 5mm Hex Key, M6x1.0 Thread - Pad Material: Black (standard) or Clear Rubber (Soft) - Weight: 1.0oz / 28g (pair)

- Lower cables for Odyssey's Gyro G3 (sold separately). - Universal fit. - Lower cables only.

- Upper cables for Odyssey's Gyro G3 (sold separately) - Universal fit. - Upper cables only.

The Slim by Four is a BMX-specific brake pad with a symmetrical shape designed for both forwards and backwards braking. A custom inner frame helps to stiffen the pad and prevents excessive braking power from being lost to flex. SPECS - Clear and Gum colored “Soft” compound pads provide extra grip on powder coated rims. - Black “Normal” compound Slim-By-Four pads are the most popular pad choice for most riders.

- Press fit designed to work the hub's non-drive side collar.

Broc Raiford can bunnyhop over a house so it’s only right that he has his own grips to hold on to. Broc’s signature grip comes in at 160mm in length and features rope detailing on the ends to tie in with Broc’s nautical theme.

The Odyssey K-Shield Linear cable features a pre-stretched inner Slic Kable covered in a linear casing to prevent binding and an outer K-Shield mesh housing for less weight over a standard steel mesh housing (2.9 oz). - Black - 60 – 65mm

As the name implies, this new version can be easily adjusted to cover 3 different lengths by utilizing the cable’s unique straddle interface connection. This tool-free feature allows the Adjustable Quik Slic Kable to be a one-size-fits-all cable for virtually every braking configuration. FEATURES - Adjustable hanger slot allows upper cable to rotate for optimum alignment. - The integrated hanger and straddle cable creates direct routing to brake arms with no bends or twists to reduce flex. - Linear K-Shield mesh housing offers higher compression rate and lighter weight than standard steel mesh. - All Odyssey Linear cables are offered with the K-Shield housing. - Specially designed and machined Volcano ferrules prevent premature housing blowout. Velcro strap included. SPECS - Housing length: 995mm - Frame requirements: Slotted cable stop and guides. 245mm (+/-3) distance from center brake boss to the front of the cable stop is recommended. - Brake requirements: Open-ended U-brake arms. - Works with most brake levers. - Velcro strap included.

- New ultra-slim 2014-T6 aluminum seat clamp with replaceable hardware and self-aligning nut. - 6061-T6 aluminum construction. - Standard 1-1/8-inch size.

One of the most important goals that Odyssey had when they sat down to work on new braking designs was to make the whole system easier to install (and remove) without sacrificing performance. They also wanted to be sure that every component would be very affordable. The Springfield lever is easy to install and remove without having to wrestle grips on and off. An ordinary hinged clamp can be bulky and expensive so a new clamping design made specifically for die-casting was used. This approach keeps the lever reliable and affordable. The lever handle is the same comfortable shape as the proven Monolever Medium blade.

This is Odyssey's top-of-the-line brake cable that ties together all of their most advanced braking technology. - Utilizes the original BMX Linear Slic Kable housing to prevent binding when the bars are rotated. - Factory installed ferrule ends with inner volcano shape to prevent housing blow out; a Linear Slic Kable standard since 2008. - Specially coated inner wire for ultra low friction, a proven feature resurrected from their once famous Brakeline cables. - Gyro lug included at one end of the inner wire for use with detanglers. - 60-65mm in length. - Black

For the Bluebird chain, Odyssey took the proven and reliable KMC 510-HX chain and added a permanently attached, factory installed half-link to one end. When the chain is trimmed to size you can easily decide whether or not to use the half-link. Original factory assembled pin joints are radically stronger than workshop assembled ones, so this is a huge benefit.

One of the most successful and popular pedals, and for good reason with its extremely simple, lightweight, inexpensive and famously durable plastic-bodied design. Often duplicated but never replicated. - High-strength plastic composite

Odyssey took their proven Linear Slic Kable housing and replaced the steel linear wire with aluminum. Utilizing the aluminum wire in the housing saves you significant weight, roughly 30%. This cable also features their specially designed “volcano” ferrules that they’ve used since 2008 to prevent housing blowouts. This Kable also comes with color-coaded inner wires and ball ends to differentiate between their regular Linear’s Race Linear Slic Kable. - Length: 60 – 65mm - Black

One of the most important goals that Odyssey had when they sat down to work on new braking designs was to make the whole system easier to install (and remove) without sacrificing performance. They also wanted to be sure that every component would be very affordable. The Springfield brake drops the two ordinary (and confusing) brake springs and replaces them with one central spring that applies the same force to each arm, requiring no additional adjustment. This makes assembly incredibly easy–just bolt it on and go. The brake arms are designed to maximize stiffness and save weight without adding excessive cost. By die-casting the arms and using shared tooling to make each side, the Springfield meets all of the original design goals, resulting in a very powerful and affordable brake.

Odyssey's original dual cable detangler system has been the industry standard since day one. Odyssey has been making the Gyro since 1986 and constantly improving it along the way. Everything you need to run a Gyro. Odyssey Gyro cables and upper and lower cable stops included.

This custom 7075-T6 aluminum pre-load bolt design is included with every Odyssey fork. - Fits both a 6mm and 8mm allen key. - Front brake cable thru-way hole for removal without disconnecting brake hardware. - Designed with an easy-cut thread groove if you cut your fork’s steerer tube down.

The Monolever was an instant classic and has become a clear favorite with pro riders around the world because of its familiar feel, smooth edges and variety of handle options.

- Straight gauge spokes with a proprietary grade of stainless steel that is as good or better than the materials used by the world’s most renowned spoke makers. - Sized and dimensioned specifically for BMX.

- 4140 Chromoly - 3 Possible peg positions for longer peg life - 14mm with 3/8-inch adapters included - 4 inches (length) x 1-3/8 inches (outer diameter) - Sold in pairs - 8.75 oz (17.5 oz for a pair)

Designed specifically for use with Odyssey's Quartet FRONT or REAR hubs. SPECS - Forged from 7075-T6 aluminum for greater strength and durability - Steel insert prevents guard deformation, prolonging bearing life

The M2 lever works with a single cable or Odyssey’s patented dual cable system. The M2 cable system improves braking power for GYRO users. - Right hand only (works flipped on the left) - M2 specific upper cable and single cable coupler included.

Odyssey is proud to offer their new tripod post. It allows for the two most popular seat angles amongst riders and it’s clean, light and easy to install. SPECS - 25.4mm diameter - 6061-T6 Aluminium, CNC machined

Mike Aitken's original signature seat size and shape.

This plastic peg features a full 4130 core with a long-lasting, fast-sliding, plastic sleeve. - 1.5-inch outer diameter - 14mm with 3/8-inch adapter - Sold individually - Weight: 7.6oz - Replacement sleeves sold separately

Designed using high-quality sealed bearings and a precision tapered wedge to keep the headset tight at all times. FEATURES - High-quality sealed bearings. - Color matched spacers included. - 10mm, 3mm and 2mm (15mm total) - Laser etched Odyssey bearings. SPECS - Campagnolo standard spec. - 1-1/8 integrated headset. - 45º tapered bearings 41.8mm outer diameter (fits 42mm BMX head tubes).

New dust cap design, with Monogram laser etched logo, for a cleaner look to accommodate a taller riding set up with less spacers. Same quality as Odyssey's Pro Headset using high-quality sealed bearings and a precision tapered wedge to keep the headset tight at all times. FEATURES - High-quality sealed bearings. - Color matched spacers included. - 15mm dust cap. With 3mm, and 2mm spacers - Laser etched Odyssey bearings. SPECS - Campagnolo standard spec. - 1 1/8-inch integrated headset. - 45º tapered bearings - 41.8mm outer diameter (fits 42mm BMX head tubes).

Chase Gouin’s signature tire. Predictable during tight turns and made to roll smooth at high speeds. Horizontal tread grooves provide shoe traction only when you need them to. This modern interpretation of one of the most popular tires ever made is used regularly by street riders too. Now available with a Special Compound tread durometer for polished indoor floors. 100 PSI, of course.

Odyssey racing spokes use butting dimensions that are tailor-made for BMX racing, and they’re still strong enough to handle some light street riding too. You’ll save roughly an ounce per wheel on 36’s. Only the best stainless steel has been used, and the gradual butting transitions are ideal for the stresses that a 20-inch wheel has to endure. - Proprietary professional-grade stainless steel. - BMX specific butting transition dimensions.

The Springfield Brake Kit will provide easy braking upgrades along with value, as the kit will be more affordable than buying each part individually. All necessary hardware will be included as well. Doesn't get much better! - One spring design - Comes with GHOST PADS - Hinged lever clamp - Medium sized lever